# generated by Slic3r 1.2.9 on Sun Mar 13 17:42:14 2016
avoid_crossing_perimeters = 0
bed_shape = 0x10,200x10,200x210,0x210
bed_temperature = 65
before_layer_gcode = 
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 2
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 T1            ;Heater off\nM104 S0 T0\nM140 S0             ;heated bed off\nM107\nG1 X0 Y0 F4000\nM84 ; motor off\nM42 P7 S0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 35
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0.38
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FFFFFF
filament_diameter = 1.7
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 65
first_layer_extrusion_width = 0.5
first_layer_height = 0.252
first_layer_speed = 50%
first_layer_temperature = 195
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.49
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 40
interface_shells = 0
layer_gcode = 
layer_height = 0.24
max_fan_speed = 100
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 100
min_print_speed = 10
min_skirt_length = 10
notes = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]_mono-PLA.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.48
perimeter_speed = 40
perimeters = 2
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 0.5
retract_layer_change = 1
retract_length = 3.6
retract_length_toolchange = 3
retract_lift = 0.252
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
seam_position = aligned
skirt_distance = 2
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 12
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 190%
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = M42 P7 S255\nG21           ;metric is good!\nG90           ;absolute positioning\nM104 S165 T1 ; debut chauffe T1\nM104 S165 T0 ; debut chauffe T0\nG28 X ; home X\nG1 X100 F3000 ; centre X\nG28 Y ; home Y\nG28 X ; home X au dessus du coupe nouille\nG28 Z ; home Z\nG92 E0        ;reset extruder\nM104 S165 T1 ; chauffe T1\nM109 S195 T0 ; attente chauffe T0
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.5
support_material_interface_speed = 30
support_material_pattern = honeycomb
support_material_spacing = 2
support_material_speed = 30
support_material_threshold = 45
temperature = 200
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 165%
top_solid_infill_speed = 35
top_solid_layers = 3
travel_speed = 100
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0